Whirlpool Ultimate Care Ii Washer Won't Spin

If the washer will not agitate or spin then you could have a broken motor coupler. When it comes time for the spin, i hear a faint, rapid clicking from the panel and smell an electrical/burning type smell.

Pin on DREAM HOME!

Try to turn the driveshaft leading from the motor by hand.

Whirlpool ultimate care ii washer won't spin. Whirlpool ® manuals can help you get the most out of your appliance, and provide important information about parts and accessories. Some of the cycles have let us hear almost a mechanical ticking almost, but we don't use the special care cycles. I replaced the lid switch a couple of months ago.

Whirlpool ultimate care ii washer and the spin cycle won't engage. The lid switch assembly prevents the washer from spinning when the lid is open. There are a variety of combinations to use for different fabrics.

Then pull it off to expose the washing machine agitator dogs. If it is frayed or has worked its way up the drive shaft, it should be replaced. Causes and repair for a whirlpool washing machine that won't spin or rinse.

My whirlpool washer will agitate but not spin. My whirlpool ultimate care ii stopped running last night with it full of water. Sometimes if it won’t shift at the first pause, lifting the lid a few times will get the gearcase to shift, but this proves the gearcase is the problem.

Spins automatically on final high spin cycle. Lid open in last 2 minutes of agitate. If there no water flow on any selection go to step 2 below picture.

If it is at start of spin/drain then the problem is very likely the lid switch. Lid open in spin cycle. close lid. If the lid switch does not have continuity, replace it.

To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If the lid switch assembly fails, the washer will not spin. It would be worth repairing if it's just has a broken motor coupler.

No pause and the timer advances to off without spinning you need a timer. If your washer is tucked into a corner, you'll want to make some space to work around. If the washer is not spinning or spinning slowly the clutch can be the problem.

When agitation stops, there is no sound coming from it. Explore front load laundry set. If the motor is, actually running and the washer will drain water but won't agitate or spin would indicate a broken motor coupler.

Explore top load laundry set. Remove and test the whirlpool washer water level switch (picture above) also known as a pressure switch. Typically when the clutch is bad the washer will wash, will pump out but will not spin or spins slowly.

This video will show how to replace the clutch on a whirlpool direct drive washer. Whirlpool ultimate care ii washer wish super large load capacity. This is the switch that stops the spin cycle immediately if you lift the lid.

Unplug the power cord for the washer (unless you already followed step 2, good for you!) turn off the water knobs and disconnect the hoses from either the washer or the tap, your choice. Unit will not enter spin cycle or drain. I advanced the dial hoping to remove the water (washer was full of water as it had been set for an extra large load cycle).

I can get it to spin on the first 2 cycles by opening and closing the lid. Never use an extension cord with your washer. If it hangs loose, it needs to be tightened.

I'm guessing it's important to note that the drum still agitates, but won't engage the spin cycle.what i tried i It's a fairly easy procedure to remove and replace the motor coupler. Check terminal connections on above parts.

There is a suggestion, however, on the inside of the lid to replace the inlet hose ever 5 years. Here is a link of a previous answer that describes the repair of a motor coupler: The water did eject, but only after making a very disconcerting racket.

If suspected flow problem is corrected, reconnect hoses and go back to step 1, otherwise, go to step 3 “test the whirlpool washer inlet valve” (skip step 2). It does not count down to the next part of the cycle either. I pulled the motor off and found that it humms when on spin cycle and will spin if i give the shaft a little.

Other things that can cause the washer to wash but not spin are the timer, water level control and transmission. If the motor is running but the washer won't spin, you could have a mechanical problem with the basket drive, the clutch or the transmission. If your timer does the pause but the washer still won't spin when the motor starts, you will need a gearcase.

I have owned it for almost 5 years now, and have never had to have it fixed or parts replaced. My whirlpool ultimate care ii model #lsb6200kqo will not spin clothes on the first or second drain cycles. Find whirlpool ® washer, dryer and kitchen appliance manuals you can download from our website.

Whirlpool Washer and Dryer Set Whirlpool washer and